Frag Swap 6/22

[Coral Hub (Nathan)]

Hey All!
I finally will have a day off to where I can swing by and visit for a little bit. I’ll be donating some items for the event but also wanted to offer 35% off the website coralhubus.com with code CHBAR35 at check out. When you place your order you’d be able to select local pickup and I can deliver it on Sunday. The code will be available until Friday so it gives me time to get everything together.


If you have any questions about products or the site just shoot me a message.

 

[MichaelB]

Hey All!
I finally will have a day off to where I can swing by and visit for a little bit. I’ll be donating some items for the event but also wanted to offer 35% off the website coralhubus.com with code CHBAR35 at check out. When you place your order you’d be able to select local pickup and I can deliver it on Sunday. The code will be available until Friday so it gives me time to get everything together.


If you have any questions about products or the site just shoot me a message.

Not sure if you keep coral or not, if so bring 3 different frags and join in on the fun as well.

 

[Coral Hub (Nathan)]

Not sure if you keep coral or not, if so bring 3 different frags and join in on the fun as well.

I do but unfortunately haven’t moved the DT to the new house yet haha. The GF and I will only be able to hangout for a few, it’s the anniversary day so I am just lucky to be able to squeeze this in haha.

 

[Invictus]

@Coral Hub (Nathan) Do you have any fragging supplies? They’re all sold out on the site. 2” plates specifically.

 

[Coral Hub (Nathan)]

@Coral Hub (Nathan) Do you have any fragging supplies? They’re all sold out on the site. 2” plates specifically.

Unfortunately no plates at the moment. I have stuff in the kiln but def forgot what I put in. I do have 1.75” though if you’re interested in those

 

[psidriven]

How thick are those plates? I’m interested in thinner plates.

 

[Coral Hub (Nathan)]

How thick are those plates? I’m interested in thinner plates.

Roughly 4 mm
The old molds did not account for shrinking so I don't have standard sizing but I do have some various sizing. like a bunch of 1.9 inch disks

 

[Coral Hub (Nathan)]

My new molds are about 3 mm thick but because I’m restarting it’s a slow process lol. Most sell out before I can even get the batch out of the kiln.

 

[psidriven]

Can you make 1-2mm thick plates or that’s too brittle?

 

[Coral Hub (Nathan)]

Can you make 1-2mm thick plates or that’s too brittle?

Yeah you’re in the area of losing a bunch once fired in the kiln

 

[ReyDeFarts]

Bump to remind folks about the 35% off and pickup at the swap!

Thanks @Coral Hub (Nathan) for being a consistent supporter of BAR. We truly appreciate you.

Now it's the club's turn to show that appreciation with their wallets!

 

[psidriven]

i ordered

 

[newfly]

Hi Nathan

How do I order online with the coupons and get it from you at the swap? I’m not going to the swap but plan on helping will later. I think I can get someone to bring it over. Your website ask for shipping address and I assume it will charge for shipping.

 

[Darkxerox]

@Coral Hub (Nathan) do you have more info on the benefits of the three different strains of phytoplankton? E.g. what's better for coral nutrition, filter feeder nutrition, sponges, etc.

 

[psidriven]

Hi Nathan

How do I order online with the coupons and get it from you at the swap? I’m not going to the swap but plan on helping will later. I think I can get someone to bring it over. Your website ask for shipping address and I assume it will charge for shipping.

there is field during checkout to enter CHBAR35 for the discount.

you just uncheck the ship to box and it'll give you the pick up box to check. i also put 'pickup at 6/22 bar swap' in notes.