Our mission

Bestest ATO out there: give me opinions, help me not build one

R

richiev

Supporting Member
BARcard
My Reefer 500 has the standard red sea gravity ATO. It takes up a lot of sump space, but I've always liked the concept and considered it very safe. Worst case scenario, a couple gallons get added, slowly because of the drip rate.

Generally I've had a separate, electronic, reef-pi controller managed, ATO pull from a secondary reservoir and refill the gravity one, a couple times a week. On a timer so if that completely failed, it would at max dump a controlled amount of water in as well.

Secondary reservoir
---electric ATO---> Primary reservoir
---gravity---> mechanical float valve
---> tank

I recently, finally, drilled a hole in my external wall and put a larger ATO reservoir out there. I ran some long tubing and a really long DC line, so I could have my reef-pin controller continue acting as the secondary->primary filler.

Recently I've started running into issues. First, the 12v DC pump i was using because I messed with something and ran it dry. I got a replacement, but it was too cheap and weak and couldn't handle the head pressure. I bought another, and it can.

Second, my tank that last couple days has been incredibly over filled. I finally tracked down why and it's the line between the primary->float somehow developed a hole and is slowly, constantly, leaking.

Third, I had some electronic issues, and need to redo my electronic ATO setup because the sensor went bad.

Anyway, I'm currently running a bunch of fans on my tank to evaporate and get my salinity back in check, but this has me rethinking everything.

The easiest thing to do would be use a single ATO pumping from the external reservoir (20 gallons) into the sump. I then could get rid of the under tank reservoir, giving me a lot more room to clean up my sump equipment placement.

However having 20 gallons directly connected to my aquarium freaks me out.

So question: how do people do this in a very safe, robust, fault tolerant, manner?

If I was to diy this I'd use the 12V pump, connect to an electronic eye in the tank, have a mechanical electronic float cutting power to the pump if the water gets to high, have a maximum run time in which case it'd shut down, have it shut down if over a longer period (an hour) it in total ran to long, and have it alert me when any of those happens. Finally have it be resettable remotely.

Am I over thinking this, and is there just a close enough version I can use out there? I don't want to buy into an apex/hydros ecosystem right now, since that'd be a big investment. If needed I can diy extend cables if there's an existing device that works.
 
sounds like you made a tunze ato. ;)

you got 3 electronic layers. if you're not using a high pressure or persitalic pump, I'd replace one or just add a mechanical float valve. my buddy swears by them.
 
Can’t say enough about the Red Sea ReefATO. As long as it stays connected to internet it hasn’t had an issue once. I’ve had the reservoir run dry, etc. it alerts you to just about anything that can go wrong. It will work without the WiFi - WiFi just gives you the quick status check if you need it.
 
psidriven said:
sounds like you made a tunze ato. ;)

you got 3 electronic layers. if you're not using a high pressure or persitalic pump, I'd replace one or just add a mechanical float valve. my buddy swears by them.
Click to expand...
Looking at it, I do think the tunze is pretty close to what I'm describing, with the networked pieces. I feel like for the price, one might as well buy a used full controller + ATO though? I guess with the used asterisk one could also try and find a used tunze...

Srt4eric said:
I had 65 gallons attached to mine and it wiped everything out...
Click to expand...
Yeah, that's what I'm afraid of. What were you using?

wazzupmac said:
Can’t say enough about the Red Sea ReefATO. As long as it stays connected to internet it hasn’t had an issue once. I’ve had the reservoir run dry, etc. it alerts you to just about anything that can go wrong. It will work without the WiFi - WiFi just gives you the quick status check if you need it.
Click to expand...
That "as long as it stays connected" gives me pause :). The lack of a secondary fail stop also makes me concerned with it. Though I imagine one fall back could be have the fill hose connect to a mechanical float valve, such as the one installed by default on red sea sumps. Unless the pump is strong enough to push through a float?
 
richiev said:
That "as long as it stays connected" gives me pause :). The lack of a secondary fail stop also makes me concerned with it. Though I imagine one fall back could be have the fill hose connect to a mechanical float valve, such as the one installed by default on red sea sumps. Unless the pump is strong enough to push through a float?
Click to expand...
If the sensor fails it shuts off and that sensor has a back up and a leak sensor that will also shut it off. “As long as it stays connected” is more about being able to monitor it. The WiFi is just for controlling it remotely. It lets me know if the reservoir is low. I use a 20G reef can but I also have a large (S850) tank and sumps that theoretically can handle an excess of 20 G which wouldn’t destroy my salinity. The app takes into consideration the input and output tube length to minimize the chance of overfill -it knows how much water it’s putting in even if sensor is stuck and shuts off after a designated amount or time.

A float switch in the sump could turn off the outlet for the ato or a salinity monitor (on my apex) would also do the trick.

I’ve had a tunze fail on a smaller tank - all was lost and the garage had an excess 5g of water on the floor.
 
wazzupmac said:
If the sensor fails it shuts off and that sensor has a back up and a leak sensor that will also shut it off. “As long as it stays connected” is more about being able to monitor it. The WiFi is just for controlling it remotely. It lets me know if the reservoir is low. I use a 20G reef can but I also have a large (S850) tank and sumps that theoretically can handle an excess of 20 G which wouldn’t destroy my salinity. The app takes into consideration the input and output tube length to minimize the chance of overfill -it knows how much water it’s putting in even if sensor is stuck and shuts off after a designated amount or time.

A float switch in the sump could turn off the outlet for the ato or a salinity monitor (on my apex) would also do the trick.

I’ve had a tunze fail on a smaller tank - all was lost and the garage had an excess 5g of water on the floor.
Click to expand...
Seems like the only complication then would be I need to build a very extended power line for the pump, rest should work.

I'll mull this route over, thanks.
 
richiev said:
Seems like the only complication then would be I need to build a very extended power line for the pump, rest should work.

I'll mull this route over, thanks.
Click to expand...
Ah F it, I can see how this would work and it basically checks every box for me. Triple bonus points that I can just buy the cheaper upgrade kit version and it'll drop in replace in the sump. Luckily I have some BRS credit saved up, so I'm going to think about it until tomorrow then buy this one.

I also use a reef wave gyre so I'm in that ecosystem already.
 
wazzupmac said:
Can’t say enough about the Red Sea ReefATO. As long as it stays connected to internet it hasn’t had an issue once. I’ve had the reservoir run dry, etc. it alerts you to just about anything that can go wrong. It will work without the WiFi - WiFi just gives you the quick status check if you need it.
Click to expand...
2nd the Red Sea ato. I have had two issues-the one I bought first (even before commercially available due to AC) -the top sensor was busted and the 2nd time the temp sensor went out about a year out. Both times were sent replacements really fast.

In between though it has been flawless just about. Plus with a Red Sea tank -just pop the sensor where the gravity ato switch goes (unless you removed it). And good to go.

Having three sensors plus the auto timer plus the leak detector is really nice. Temp probe is a nice add on.
 
I installed a Red Sea ATO today. First impressions are good. The notifications and controls they have in the app are exactly what I would want, including a report of total volume in the day. I also really like the detailed water level visual it gives, and the backup sensors. The controller was easy to setup, and connecting everything was easy.

The wire and tubing was quite long, but too short for my outside ATO. For the tubing I used some other tubing I had handy, and will later replace with some more appropriate (thicker) tubing. The pump power line I built an extension cord for by buying some similar 2-hole waterproof DC connectors online and soldering them to a long DC cable I have.

The install into the sump was very very easy. I was expecting to have to drill or something, but it took longer for my to unscrew the old float valve then install the new setup.

The pump is very strong. I have around 20ft of tubing and has about 2feet of head pressure, plus some hills in the tubing routing, and the pump has no trouble with it. The pump also does a great job pulling almost every drop off water from the ATO reservoir because the inlet is at the very bottom.

Overall great purchase. I hope Red Sea continues on the hardware path. I know there's tank complaints, but the red sea hardware has been great in my experience, and the integration is very wonderfully done to their aquarium line.

Thanks for the advice!
 
You must log in or register to reply here.
Back
Top