grizfyrfyter
Guest
Loving this purple rim Blasto.
My 170g cube
- Thread starter grizfyrfyter
- Start date
grizfyrfyter
Guest
This baby jawbreaker won't stay attached so I put him in jail.
ofzakaria
Guest
Ha ha. Did the job thuThis baby jawbreaker won't stay attached so I put him in jail.
Sent from my SM-G960U using Tapatalk
grizfyrfyter
Guest
There has been a development in the CO2 scrubber. I noticed a couple teaspoons of water in the first chamber. The media wasn't wet but it's was enough for me to change things. I took the media out of the first cannister and it's now being used as a moisture trap.
grizfyrfyter
Guest
New rack in the frag tank
grizfyrfyter
Guest
No but I will have magnet ones after I get the next batch of magnets.im kinda glad i waited? but those wont work with my euro brace
Rostato
Guest
Mine always collects some water, but it never effected anything.
Sent from my iPhone using Tapatalk
That’s a creative design, I especially like how the frags would be tilted toward center a bit. Reminds me of a planted living wall, but for coral frags.New rack in the frag tank
grizfyrfyter
Guest
A cube isn't the optimal setup for a frag tank so I'm trying to maximize space.
The angle of the plug mounts serves two purposes. The first is that it sets the coral at an angle where more surface area gets light. Second is that it makes the frag rack stronger than a 90 degree angle, more surface area for layer adhesion. I tested a 90 degree version just to prove a point to someone, it was strong enough to hold a frag but it only took a little pressure with a finger to break off the part.
I need to order more magnets and tweak the design for them but at a little over $4 ea and 8 magnets total, they won't be cheap.
The angle of the plug mounts serves two purposes. The first is that it sets the coral at an angle where more surface area gets light. Second is that it makes the frag rack stronger than a 90 degree angle, more surface area for layer adhesion. I tested a 90 degree version just to prove a point to someone, it was strong enough to hold a frag but it only took a little pressure with a finger to break off the part.
I need to order more magnets and tweak the design for them but at a little over $4 ea and 8 magnets total, they won't be cheap.
grizfyrfyter
Guest
Fuzzy little homewrecker, grow you little bastard.
WD is showing good PE now too.
WD is showing good PE now too.
grizfyrfyter
Guest
My daughter (my normal frag swap proxy) won a pair of Kimmies Picasso clowns today.
ashburn2k
Supporting Member
Another frag swap?My daughter (my normal frag swap proxy) won a pair of Kimmies Picasso clowns today.
Sent from my iPhone using Tapatalk Pro
grizfyrfyter
Guest
Yup. 209 reef club Facebook group had a swap today.
grizfyrfyter
Guest
So. Had more moisture collecting in the second scrubber chamber and skimmate collecting in the first chamber. I put the media cannister back in the first chamber but no media in it. I had to change out the media in the scrubber since it actually got wet this time.
I'm going to design and print a new Skimmer lid that should keep the scrubber from collecting skimmate. While I'm at it, I will probably design a neck cleaner now that I have an external collection jug for the skimmer.
I'm going to design and print a new Skimmer lid that should keep the scrubber from collecting skimmate. While I'm at it, I will probably design a neck cleaner now that I have an external collection jug for the skimmer.
grizfyrfyter
Guest
Clams.
grizfyrfyter
Guest
Got some used battery backups for $10. Waiting on cables to make sure they work.
grizfyrfyter
Guest
The small one is, big one was $100 at a shop in Stockton
grizfyrfyter
Guest
This bubbly goof is going for a walk and leaving babies behind.
